Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
What are your opinions about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is easily easily accessible, the project can move quickly; if you need to open up a wall surface to eliminate the old bathtub and also place the brand-new bath tub, the job is much harder. In either situation, the job is within a home handyman's abilities, although you will require an assistant to move out the old tub and set in the brand-new one. Make certain you have certified on your own for the task as well as fit trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you start. Chances are you may need a specialist plumber to make tube connections.
This article will certainly help you mount a brand-new bathtub in your restroom if you have already bought a brand-new tub as well as don't need to alter the setup of your previous water system pipelines.
Your devices and product checklist ought to make up the following:
Getting ready for the Installment
To start with, the sustaining frame supplied with the bathroom must be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you should do is detach the water. After doing so, activate the taps to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Prior to going on to fit the new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the called for position. The wooden boards are valuable in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to ensure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost adaptable tap port to the suitable supply pipe by making a compression join; after that do the same for the various other faucet.
Activate the supply of water as well as inspect all joints and new pipework for leakages as well as tighten them if required. Load the bath tub and also check the overflow electrical outlet and the normal outlet for leakages.
Finally, deal with the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub must wait until the tub has actually been utilized a minimum of when as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap as well as the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bathroom and also the tiling, leading to complications with moisture and also feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to enable the movement experienced when the tub is in use. The sealer can crack fairly early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very excited about How to Install a Bathtub Yourself and I am assuming you liked my piece. Those who enjoyed reading our blog post please remember to pass it around. Thank you so much for going through it.
Get industry-leading emergency plumbing. Report this page